SNAP SMARTER, SNAP BETTER WITH NuSnaps

Our magnetic boat snaps are built to withstand the elements, NuSnaps products are engineered for durability and are resistant to ripping and corrosion in even the toughest conditions. We have encased the N52 Neodymium snaps with 2205 stainless steel to prevent corrosion.

Proud to be Veteran Owned & Family Operated!!

(Patent: US 11,980,258 B2)

HOW DOES IT WORK?

HOW DOES IT WORK?

N52 Neodymium Magnets !!! NuSnaps in Action!

Magnetic Boat Cushion Snaps

As seen in video:  That is not edited, turn the volume on and you can hear the hands free NuSnap securing the cushion!

Up to 11-lbs pull force per snap!!! Can be installed on any vertical or horizontal surface.

Left side of cooler is utilizing the "Surface Mount NuSnap" to secure the cushion.

Right side of the cooler is Utilizing the "Recessed Flush Mount NuSnap" to secure the cushion.

NuSnaps are designed to snap and unsnap to your cushion. When its time for new cushions or your going to reupholster, simply unsnap and re-snap to your new cushions. These snaps are meant to last the lifetime of your boat so your only buying them once!

All cushions require ample amount of snaps to secure them to the deck. With all cushions being different,  a rule of thumb guide is a 12"x18" seat cushion would require (4) one snap in each corner like the four configuration on dice. A 24"x48" seat cushion would require (6) one snap in each corner, one center front and one center back, like the six configuration on dice.  All boats have different high wind areas at speed so after installation on the initial run, it is recommended that you monitor the cushions at speed to see if there is any uplift or cupping at each cushion. For example, cushions that face high wind situations such as aft bench seating may require extra placement of snaps on the windward side to ensure wind does not get under the cushion and cause up draft cupping.  We recommend snaps not be more than 16-18 inches apart on high windward sides of the cushion.

(Patent: US 11,980,258 B2)

Featured Products

A close up of the bottom part of a metal object.

NUSNAP SURFACE MOUNT FASTENERS 

A close up of the top of a metal object

NUSNAP RECESSED MOUNT FASTENERS 

Three metal magnetic fasteners for a can cooler.

NUSNAP "Hold My Beer" Mount Anywhere Magnetic Koozie

A picture of boats in the water.

Revolutionizing Fastening Solutions 

Revolutionizing Fastening Solutions 

At NuSnaps, we've engineered a groundbreaking solution to transform how you fasten cushions and secure items requiring a snap-down mechanism. Our magnetic snaps redefine the traditional approach, eliminating the need for friction snaps and introducing a new era of durability and convenience. We have reusable snaps that are durable and can be safely removed and used over and over on new or reupholstered cushions; our snaps will not rust. Experience long-lasting durability with our magnetic snaps that are built for corrosion prevention. NuSnaps ensures your fastening solutions remain robust in any boating or outdoor environment.

Key Features

Key Features
A group of boats in the water near each other.

Effortless Fastening

Say goodbye to the hassle of friction snaps. Our magnetic snaps are great for tight or hard-to-reach spaces as they are self-seating and provide a seamless and efficient fastening experience, saving you time and effort.

A group of boats parked in the water.

Versatility Redefined

Whether you're a boating enthusiast or someone in need of reliable snap solutions, NuSnaps is designed to cater to various applications, offering unparalleled versatility.

A sail boat is shown in the ocean.

Innovative Technology

No one else can provide these snaps as they are a new, innovative, patented product and one-of-a-kind snaps.

A group of boats in the water at a marina.

Durable Design

Built to withstand the elements, NuSnaps products are engineered for durability and are resistant to ripping and corrosion in even the toughest conditions. We have encased the N52 Neodymium snaps with 2205 stainless steel to prevent corrosion.

A bunch of boats are parked in the water

Seamless Replacement

Easily replace your existing friction snaps with NuSnaps – a seamless transition for enhanced performance and longevity. Our snaps are versatile and easily transferrable from cushion to cushion or boat to boat.

A view of boats in the water at sunset.

Experience the Future of Fastening

Join the boating community and outdoor enthusiasts who trust NuSnaps for superior fastening solutions. Explore our range of magnetic accessories and snap buttons and revolutionize the way you secure your belongings.

For any questions, feel free to contact us

Surface Mount NuSnap

Surface Mount NuSnap

This video shows the surface mount system.

Tip: Most boats with existing snaps you just need to uninstall the old snap hardware and using the same holes replace with your NuSnaps hardware. Done! (This is assuming your original snaps were installed in the correct locations, we recommend snaps not be more than 16-18 inches apart on high windward sides of the cushion)

If this is a new install or not using the existing holes from the original snaps:

Attention: If your cushion has both horizontal and vertical mounting snaps, pay close attention to the sequence below on marking and drilling the different surface holes. Failure to do so will cause vertical holes to be misaligned.

Step#1: Install all your NuSnap Magsnaps to your cushion.

Step#2: place the cushion with the NuSnaps installed exactly where you intend to place it on the boat, with a wax pencil, trace the outer edge of only the  "Horizontal Surface" cushion snaps on to the boat. (Do not trace vertical surface snaps at this time if you have them).

Step#3: With a stainless steel 82 degree #8 x 3/4" long flathead screw, only attach the "Horizontal" Surface Mount Anchor at the center mark. Screw must sit flush with anchor. Place cushion down to inshore fit.

Setp#4: With the cushion down and the horizontal NuSnap Magsnaps & Surface Mounts connected. With a wax pencil, trace the outer edge of the  "Vertical Surface" cushion snaps on to the boat. 

Step#5: With a stainless steel 82 degree #8 x 3/4" long flathead screw, attach the Vertical Surface Mount Anchor at the center mark. Screw must sit flush with anchor. Place cushion down to inshore fit. Done!

(Patent: US 11,980,258 B2)

Recessed Flush Mount NuSnap

Recessed Flush Mount NuSnap

This  Video shows the NuSnap flush mount system. This low-profile design sits flush with the surface in a 1-1/8th inch diameter, 5/16th inch depth counterbore. We recommend snaps not be more than 16-18 inches apart on high windward sides of the cushion.

Attention: If your cushion has both horizontal and vertical mounting snaps, pay close attention to the sequence below on marking and drilling the different surface holes. Failure to do so will cause vertical holes to be misaligned. 

Step#1: Install all your NuSnap Magsnaps to your cushion.

Step#2: place the cushion with the NuSnaps installed exactly where you intend to place it on the boat, with a wax pencil, trace the outer edge of only the  "Horizontal Surface" cushion snaps on to the boat. (Do not trace vertical surface snaps at this time if you have them). 

Step#3: Drill the hole with a 1-1/8" Spade or forstner bit for the "Horizontal Surface" snaps only.

Note: (4th,5th & 6th steps are only if you have the vertical hang tab type cushion, If not skip to Step#7)

Setp#4: Temporarily Connect the Flush Mount Anchor to the cushion snaps. Place the cushion down with the horizontal NuSnap Magsnaps & Flush Mount sitting dry-fit in these newly drilled holes. 

Step#5: with a wax pencil, trace the outer edge of the  "Vertical Surface" cushion snaps on to the boat. 

Step#6: Drill the holes with a 1-1/8" Spade or forstner bit for the "Vertical Surface" snaps. 

Step#7: Put the cushion aside & apply 3M 5200 to the sidewalls of the flush mount anchors & insert into the boat side holes, wipe clean any excess, allow 48hrs to cure before attaching the cushion.

Tools Needed: Drill, 1-1/8" spade/forstner bit, 3M-5200, Wax Pencil.

How does it work? N52 - Magnets...
Does it rust? No way, man!!
N52 Neodymium encased in 2205 Stainless Steel!!

Installation Tips:

Tip #1. For "hang tag style cushions" If the fabric is thick, cut away access material and make the hole a little bigger than needed to get the snap stem through the fabric. On a flat surface, lay a piece of wood down and place the cushion with the mag-snap through the fabric button side up on top of the wood. With a rubber mallet give a soft whack to seat the button cap to the Mag-snap sandwiching the fabric in between. Video of this installation coming soon!

Tip#2. Do not install the NuSnap Magsnaps close to any sewing seams. This may seat the NuSnap crooked and cause issues. Button Cap must sit flush with the Mag-Snap.

Tip#3. Use latex gloves, long sleeves and have a shop vac handy while drilling the Flush Mount holes. Fiberglass does not feel good on skin!!

If you have any questions on installation, always feel free to give us a call. Anchors Away!

(Patent: US 11,980,258 B2)

"Hold My Beer"

The "Hold My Beer" Mount Anywhere NuSnap Magnetic Koozie Holder. Mount the stainless NuSnap surface anchor anywhere on your boat, cooler, fence, desk, anywhere! Attach our NuSnap magsnap to any Koozie. This is not disposable! When your Koozie gets nasty just unsnap it and re-snap to any koozie you like! 

Comes with a Koozie and (1) NuSnap Surface Mount, (1) NuSnap Magsnap & (1) Button Cap

(Patent: US 11,980,258 B2)